ORE SORTING SUCCESS AT LINKA TUNGSTEN PROJECT
Released
Released
Announcement PDF
ASX ANNOUNCEMENT
18 June 2026
15-17 Old Aberdeen Place
West Perth, WA, 6005
P +61 8 6245 0870
F +61 8 9322 5230
contact@vikingmines.com
1
ASX:VKA, OTC:VKALF
vikingmines.com
ORE SORTING SUCCESSFULLY PRODUCES SEPARATE
PRODUCTS AT LINKA PROJECT
• X-ray Transmission (XRT) ore sorting testwork completed by TOMRA on two samples
from the Linka Tungsten Project has successfully separated mineralised feed into
discrete product and waste streams.
• Conquest Pit sample directed 67.8% of sample mass to product streams, with high
abundance of visible scheelite confirmed in the high-grade product fraction under
ultraviolet light.
• Linka Stockpile sample directed 56.1% of sample mass to product streams,
demonstrating ore sorting potential for upgrading existing surface stockpiles.
• Testwork applied TOMRA’s newly released CONTAIN™ deep-learning inclusion-
detection software across a three-stage cascade sorting configuration.
• Ore sorting offers two potential value pathways: pre-concentration of run-of-mine feed
to lift plant feed grade and upgrading of existing grade stockpiles.
• Product fraction assays are pending, with results expected in the second half of July
2026, and will quantify the grade and recovery performance of each stream.
Figure 1; High-grade sorted fraction (Set 1) from the Conquest Pit sample under ultraviolet light, showing characteristic
blue-white fluorescence of scheelite. Visual estimate containing between ~1.5% to ~3.5% scheelite
(~1.2% to ~2.8% WO3). Refer to Appendix 1. Assay results expected late July 2026.
Cautionary Statement: Visual estimates of mineral presence should never be considered a proxy or substitute for laboratory
analyses where concentrations or grades are the factor of principal economic interest. Visual estimates also potentially provide no
information regarding impurities or deleterious physical properties relevant to valuations.
2
ASX:VKA, OTC:VKALF | vikingmines.com
Viking Mines Limited (ASX: VKA, OTCID: VKALF) ("Viking" or "the Company") is pleased to
report positive initial results from X-ray Transmission (XRT) ore sorting testwork completed by
TOMRA at its Test Center in Wedel, Germany, on mineralised material from the Linka Tungsten
Project in Nevada, USA. The First Inspection testwork was undertaken on two samples, a ~19.4 kg
Conquest Pit sample and a ~19.4 kg Linka Stockpile sample, each crushed and screened to
+10mm – 40mm, to assess the amenability of Linka mineralisation to sensor-based pre-
concentration.
Viking Mines Managing Director & CEO Julian Woodcock said:
“These initial ore sorting results are an important step in our strategy to define a rapid low-CAPEX,
pathway to production at Linka. The clear presence of scheelite in the high-grade sorted fraction
gives encouragement that the technology could have direct benefits to the Project.
“Ore sorting is in place for many operating tungsten mines globally. If Viking can confirm that we
are able to utilise the technology to reject a meaningful proportion of waste prior to milling, gravity
and flotation, we have the potential to both upgrade run-of-mine feed and unlock value from our
existing stockpiles.
“We look forward to receiving the product assays in July, which will allow us to quantify the grade
uplift and recovery achieved. Subsequently, we will be able to determine the cost benefit of
applying this technology in our conceptual process flow sheet for the Linka Project.”
ORE SORTING TESTWORK
The testwork was conducted on TOMRA’s X-ray Transmission (XRT) sorting platform, which
discriminates material on the basis of atomic density and is well suited to the detection of dense
tungsten-bearing minerals such as scheelite. XRT technology works by exploiting the difference
in attenuation of X-ray radiation between tungsten-bearing ore and barren rock. Due to its ultra
high atomic density, tungsten strongly absorbs X-rays. As a result, tungsten appears as distinct,
dense inclusions in XRT images.
The testwork program incorporated TOMRA’s newly released CONTAIN™ software, a deep-
learning module that identifies mineralised inclusions within host rock particles, alongside the
established OBTAIN™ detection technology.
Each sample was processed through a three-stage cascade sorting configuration (Figure 4),
designed to progressively recover mineralised particles: Stage 1 ejected high-grade inclusions,
Stage 2 ejected lower-grade inclusions, and Stage 3 applied the CONTAIN™ module to recover
remaining inclusion-bearing particles. This produced four output streams: High Grade Inclusions,
Low Grade Inclusions, CONTAIN™ Inclusions and Waste, as summarised in Table 1.
Table 1; Mass balance of TOMRA XRT cascade sorting testwork for the Conquest Pit and Linka Stockpile samples.
Product fraction assays are pending.
Product Stream
Conquest Pit (0.8% WO3) Linka Stockpile (0.5% WO3)
Mass (kg) Mass (%) Mass (kg) Mass (%)
High Grade Inclusions 2.4 12.1 0.7 3.4
Low Grade Inclusions 7.2 36.9 5.2 26.9
CONTAIN™ Inclusions 3.6 18.6 5.0 25.8
Waste 6.3 32.5 8.5 43.9
Total Feed 19.4 100 19.4 100
Mass to Product (excl. Waste) 13.1 67.8 10.9 56.1
3
ASX:VKA, OTC:VKALF | vikingmines.com
For the Conquest Pit sample, approximately 68% of feed mass reported to the three product
streams, with the balance rejected as waste (Figure 2). Visible scheelite was confirmed in the high-
grade product fraction under ultraviolet (blacklight) illumination (Figure 1). For the Linka Stockpile
sample, approximately 56% of feed mass reported to product streams (Figure 3). Product fraction
assays have not yet been completed; TOMRA does not assay sorted fractions in order to retain
independence, and the fractions have been returned to the Company’s metallurgical laboratory
in Canada for analysis, with results expected in the second half of July 2026.
Figure 2; TOMRA XRT sorted fractions from the Conquest Pit sample: A: Set 1 High Grade Inclusions, B: Set 2 Low
Grade Inclusions, C: Set 3 CONTAIN Inclusions and D: Waste (clockwise from top left).
4
ASX:VKA, OTC:VKALF | vikingmines.com
Figure 3; TOMRA XRT sorted fractions from the Linka Stockpile sample: A: Set 1 High Grade Inclusions, B:
Set 2 Low Grade Inclusions, C: Set 3 CONTAIN Inclusions and D: Waste (clockwise from top left).
5
ASX:VKA, OTC:VKALF | vikingmines.com
Figure 4; Three-stage cascade XRT sorting flow sheet applied to each sample, producing four output streams (High
Grade, Low Grade and CONTAIN™ Inclusions, and Waste). Source: TOMRA.
6
ASX:VKA, OTC:VKALF | vikingmines.com
STRATEGIC SIGNIFICANCE
If confirmed by the pending assays, ore sorting could provide two distinct sources of value for the
Linka Tungsten Project.
1. Pre-concentration of run-of-mine feed would allow waste to be rejected ahead of the
processing plant, lifting plant feed grade thereby maximising metric tonne units of
tungsten in process.
2. Ore sorting could be applied to upgrade the Company’s existing surface stockpiles,1
potentially converting lower-grade material into a viable plant feed or saleable product.2
These results build on the Company’s broader metallurgical program3
at Linka and will be
integrated into the conceptual processing flowsheet4
being developed by Mineral Technologies
for the ~300,000 tonne-per-annum (300ktpa) processing model.
NEXT STEPS
Subject to confirmation by the pending assays, the Company’s near-term workstreams for the ore
sorting program include:
• Evaluating ore sorting effectiveness and quantifying grade and recovery performance once
product fraction assays are received (expected second half July 2026).
• Assessing the application of ore sorting to upgrade existing surface stockpiles.
• Completing gravity and flotation testwork on the ore sorting products at Base Met Labs to
replicate the proposed process flow diagram.
• Reviewing the conceptual flowsheet to incorporate an ore sorting stage.
• Obtaining a TOMRA equipment quotation to support the 300ktpa CAPEX model being
developed by Mineral Technologies.
END
This announcement has been authorised for release by the Board of the Company.
Julian Woodcock
Managing Director and CEO
Viking Mines Limited
For further information, please contact:
Michaela Stanton-Cook - Company Secretary
Viking Mines Limited
+61 8 6245 0870
Learn more about Viking Mines via our investor hub here.
1
ASX Announcement 21 May 2026, Linka Tungsten Project Field Campaign Identified Additional Stockpiles.
2
ASX Announcement 9 June 2026, Linka Stockpile Sampling Delivers up to 1.1% WO3.
3
ASX Announcement 10 June 2026, Linka Tungsten Project Recovery Improved to 76.0% at 56.9% WO3 Grade.
4
ASX Announcement 27 April 2026, Conceptual Process Established for the Linka Tungsten Project.
7
ASX:VKA, OTC:VKALF | vikingmines.com
APPENDIX 1 – SAMPLE LOCATION AND ASSAY RESULTS TABLES
Competent Persons Statement – Exploration Results
Information in this release that relates to Exploration Results is based on information compiled by Mr Julian Woodcock, who is a
Member of the Australian Institute of Mining and Metallurgy (MAusIMM(CP) – 305446). Mr Woodcock is a full-time employee of
Viking Mines Ltd. Mr Woodcock has sufficient experience which is relevant to the style of mineralisation and type of deposit under
consideration and to the activity being undertaken to qualify as a Competent Person as defined in the 2012 Edition of the
‘Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves’. Mr Woodcock consents to the
disclosure of the information in this report in the form and context in which it appears.
Competent Persons Statement – Metallurgical Testwork
The information in this announcement that relates to Exploration Results from metallurgical test work is based on, and fairly
represents, information and supporting documentation compiled by Mr Peter Adamini, BSc (Mineral Science and Chemistry), who
is a Member of The Australasian Institute of Mining and Metallurgy (AusIMM). Mr Adamini is a full-time employee of SGS Australia
owned Independent Metallurgical Operations Pty Ltd, a wholly owned subsidiary of SGS Australia Holdings Pty Ltd, and has
sufficient experience that is relevant to the style of mineralisation and type of deposit under consideration and to the activity being
undertaken to qualify as a Competent Person as defined in the 2012 Edition of the ‘Australasian Code for Reporting of Exploration
Results, Mineral Resources and Ore Reserves’. Mr. Adamini is an independent consultant engaged by Viking Mines Limited for
metallurgical representation. Mr Adamini consents to the disclosure of the information in this report in the form and context in
which it appears.
Forward-Looking Statements
This document may include forward-looking statements. Forward-looking statements include, but are not limited to, statements
concerning Viking Mines Limited’s planned exploration programme and other statements that are not historical facts. When used
in this document, the words such as "could," "plan," "estimate," "expect," "intend," "may”, "potential," "should," and similar
expressions are forward-looking statements. Although Viking Mines Limited believes that its expectations reflected in these
forward-looking statements are reasonable, such statements involve risks and uncertainties and no assurance can be given that
actual results will be consistent with these forward-looking statements.
8
ASX:VKA, OTC:VKALF | vikingmines.com
APPENDIX 2 – JORC CODE, 2012 EDITION – TABLE 1
JORC Table 1, Section 1 – Sampling Techniques and Data
Criteria JORC Code explanation Commentary
Sampling
techniques
Nature and quality of sampling (e.g. cut channels, random chips, or specific
specialised industry standard measurement tools appropriate to the minerals
under investigation, such as downhole gamma sondes, or handheld XRF
instruments, etc.). These examples should not be taken as limiting the broad
meaning of sampling.
Metallurgical Sample
Collection of loose rocks on surface approximately 10-20cm in diameter from each of the 2 sample
locations (Linka Stockpile and Conquest Pit). Samples collected were packed in to plastic buckets for
transportation to the metallurgical laboratory for preparation prior to shipping to Germany for the
TOMRA testwork. Weights of each of the samples collected are approximately 20kg (40kg in total).
Include reference to measures taken to ensure sample representivity and the
appropriate calibration of any measurement tools or systems used.
Metallurgical Sample
Samples are deemed representative of the target mineralisation being sampled based on visual
characteristics. It is unknown if the samples are representative of the original insitu material due to rocks
being collected from loose material on surface and not being insitu.
Aspects of the determination of mineralisation that are Material to the Public
Report. In cases where ‘industry standard’ work has been done this would be
relatively simple (e.g. ‘reverse circulation drilling was used to obtain 1 m samples
from which 3 kg was pulverised to produce a 30 g charge for fire assay’). In other
cases more explanation may be required, such as where there is coarse gold that
has inherent sampling problems. Unusual commodities or mineralisation types
(e.g. submarine nodules) may warrant disclosure of detailed information
Metallurgical Sample
Loose rocks collected form surface and delivered to the metallurgical laboratory for sample preparation
(crushing and screening) prior to being shipped to TOMRA in Wedel, Germany for ore sorting testwork.
Drilling
techniques
Drill type (e.g. core, reverse circulation, open-hole hammer, rotary air blast,
auger, Bangka, sonic, etc.) and details (e.g. core diameter, triple or standard
tube, depth of diamond tails, face-sampling bit or other type, whether core is
oriented and if so, by what method, etc.).
Not applicable, no drilling being reported.
Drill sample
recovery
Method of recording and assessing core and chip sample recoveries and results
assessed.
Not applicable, no drilling being reported.
Measures taken to maximise sample recovery and ensure representative nature
of the samples.
Not applicable, no drilling being reported.
Whether a relationship exists between sample recovery and grade and whether
sample bias may have occurred due to preferential loss/gain of fine/coarse
material.
Not applicable, no drilling being reported.
Logging
Whether core and chip samples have been geologically and geotechnically
logged to a level of detail to support appropriate Mineral Resource estimation,
mining studies and metallurgical studies.
Not applicable, no drilling being reported.
Whether logging is qualitative or quantitative in nature. Core (or costean,
channel, etc.) photography.
Not applicable, no drilling being reported.
9
ASX:VKA, OTC:VKALF | vikingmines.com
Criteria JORC Code explanation Commentary
The total length and percentage of the relevant intersections logged. Not applicable, no drilling being reported.
Subsampling
techniques and
sample
preparation
If core, whether cut or sawn and whether quarter, half or all core taken. Not applicable, no drilling being reported.
If non-core, whether riffled, tube sampled, rotary split, etc. and whether sampled
wet or dry.
Metallurgical Sample
Samples were collected dry. No splitting was undertaken in the field.
For all sample types, the nature, quality and appropriateness of the sample
preparation technique.
Metallurgical Sample
The sample preparation, blending and sub-sampling techniques are appropriate for this material’s
mineralogical makeup.
Quality control procedures adopted for all subsampling stages to maximise
representivity of samples.
Metallurgical Sample
No QAQC samples were utilised by Viking. The metallurgical laboratory inserted blanks and standards
which contained WO3 grades similar to the assayed samples WO3 head grades.
Measures taken to ensure that the sampling is representative of the in-situ
material collected, including for instance results for field duplicate/second-half
sampling.
Metallurgical Sample
Insitu material has not been sampled. No duplicates taken. On completion of the metallurgical testwork
programme, the metallurgical balance will be used to verify the head grade assays.
Whether sample sizes are appropriate to the grain size of the material being
sampled.
The Competent Person considers the current methods and processes described as appropriate for this
style of mineralisation due to the grade of mineralisation being reported. Sample size of the metallurgical
sample is appropriate both due the grades being grade of the mineralisation and the large samples
collected.
Quality of
assay data and
laboratory
tests
The nature, quality and appropriateness of the assaying and laboratory
procedures used and whether the technique is considered partial or total.
Metallurgical Sample
The assaying technique utilised a lithium metaborate/lithium tetraborate (50/50) fusion melt followed by
nitric acid dissolution with the resulting solution analysed by an ICP OES/MS. This technique is
considered to be total.
For geophysical tools, spectrometers, handheld XRF instruments, etc., the
parameters used in determining the analysis including instrument make and
model, reading times, calibrations factors applied and their derivation, etc.
No data has been reported of this type.
Nature of quality control procedures adopted (e.g. standards, blanks, duplicates,
external laboratory checks) and whether acceptable levels of accuracy (i.e. lack of
bias) and precision have been established.
Metallurgical Sample
No QAQC samples were utilised by Viking. The metallurgical laboratory inserted blanks and standards
which contained WO3 grades similar to the Viking’s assayed samples WO3 head grades. This achieved
acceptable levels of accuracy and removed bias.
Verification of
sampling and
assaying
The verification of significant intersections by either independent or alternative
company personnel.
Not applicable, no drilling being reported.
The use of twinned holes. Not applicable, no drilling being reported.
Documentation of primary data, data entry procedures, data verification, data
storage (physical and electronic) protocols.
Metallurgical Sample
Samples are packaged into plastic buckets prior to shipping. Sample details are recorded in a
spreadsheet and then uploaded into Viking’s Maxwell Datashed database.
Discuss any adjustment to assay data. Assay results are reported as W% and converted to WO3% by multiplying by 1.2611.
10
ASX:VKA, OTC:VKALF | vikingmines.com
Criteria JORC Code explanation Commentary
Location of
data points
Accuracy and quality of surveys used to locate drillholes (collar and downhole
surveys), trenches, mine workings and other locations used in Mineral Resource
estimation.
Metallurgical Sample
No drilling being reported. Sample locations provided are approximate area where the samples were
collected from. Composite sample collected for each area is composed of loose rocks collected from
within an approximate15m radius of the reported sample coordinate.
Specification of the grid system used. The adopted grid system is NAD83/UTM Zone 11N and all data are reported in these coordinates.
Quality and adequacy of topographic control.
Publicly available LiDAR data from the USGS is at 1m accuracy and considered of a high quality and has
been used to determine the elevation of the samples collected.
Data spacing
and
distribution
Data spacing for reporting of Exploration Results. Not applicable.
Whether the data spacing and distribution is sufficient to establish the degree of
geological and grade continuity appropriate for the Mineral Resource and Ore
Reserve estimation procedure(s) and classifications applied.
Not applicable.
Whether sample compositing has been applied.
Metallurgical Sample
Sample assay results have not been composited. Physical samples collected are consider a composite
sample via the collection of multiple loose rocks from the sample locations to provide sufficient material
for the metallurgical testwork programme.
Orientation of
data in relation
to geological
structure
Whether the orientation of sampling achieves unbiased sampling of possible
structures and the extent to which this is known, considering the deposit type.
Metallurgical Sample
Unknown, the mineralisation sampled was not insitu.
If the relationship between the drilling orientation and the orientation of key
mineralised structures is considered to have introduced a sampling bias, this
should be assessed and reported if material.
Not applicable, no drilling being reported.
Sample
security
The measures taken to ensure sample security.
Metallurgical Sample
Samples were collected in the field by Viking contract geophysics team and shipped to Base Met Labs in
Tucson, Arizona. Samples were then prepared and shipped to TOMRA in Germany. Standard shipping
protocols apply with consignment notes confirming delivery.
Audits or
reviews
The results of any audits or reviews of sampling techniques and data. The Company has conducted no audits or reviews of the sampling techniques and data.
JORC 2012 Table 1, Section 2 – Reporting of Exploration Results
Criteria JORC Code explanation Commentary
Mineral
tenement and
Type, reference name/number, location and ownership including
agreements or material issues with third parties such as joint ventures,
partnerships, overriding royalties, native title interests, historical sites,
wilderness or national park and environmental settings.
Tenements and location
The USA Tungsten Project Lode Mineral Claims are located in the state of Nevada in the USA. Details of the
Mineral Claims are presented in the table below:
11
ASX:VKA, OTC:VKALF | vikingmines.com
Criteria JORC Code explanation Commentary
land tenure
status
Project State County Type Holder Quantity
Linka Nevada Lander Unpatented
BLK Group LLC 10
Viking Tungsten LLC 91
Alpine Nevada Pershing Unpatented BLK Group LLC 4
Long Nevada Pershing Unpatented
BLK Group LLC 4
Viking Tungsten LLC 12
Ragged Top Nevada Pershing Unpatented
BLK Group LLC 8
Viking Tungsten LLC 30
Terrell Nevada Nye Unpatented
BLK Group LLC 10
Viking Tungsten LLC 56
Victory Nevada Nye Unpatented Kircher Mine Development LLC 8
Third Party Interests
Viking Mines Ltd has signed a binding term sheet to acquire a 100% interest in the project BLK Group LLC
Mineral Claims and currently holds no ownership. Viking can acquire 100% interest in the claims by paying a
total of US$2.88M over a staged 7 year period. BLK group will retain a 2% NSR on all minerals recovered from
mineral claims, and Viking retains the option to buy down 1% of the NSR for US$2M.
Native Title, Historical sites and Wilderness
There are no known registered historical sites over the Project Mineral Claims. The Mineral Claims are
registered with the Bureau of Land Management. The Linka Project has split federal agency responsibility with
the Bureau of Land management managing approximately half of the claims and the US Forestry Service the
other half. All the remaining projects fall under the jurisdiction of the BLM.
The security of the tenure held at the time of reporting along with any
known impediments to obtaining a licence to operate in the area.
The tenements are held in good standing by BLK Group LLC. To the best of Vikings knowledge, all annual
claim payments are up to date. There are no known impediments to obtaining a licence to operate in the area.
The US process is to file either a notice of intent or Plan of Operations to the responsible Federal Agency to
obtain permits for drilling. The Company does not know of any reason why these permits would not be
granted once the process if followed and the required bond payment made.
Exploration
done by other
parties
Acknowledgment and appraisal of exploration by other parties.
Linka Mine: The area was staked in 1941 by Steve Linka of Austin, NV. In 1943-44, the mine produced 2,420
tons of ore averaging 0.69% WOз. Consolidated Uranium Mines purchased the property in 1953, sunk a
vertical shaft to 210 feet and drove approximately 1,000 feet of drifts and cross-cuts on the 150’ level.
Additional production included; 4,000 tons of ore averaging 0.98% WOз between 1951 and 1956 and 60,000
tons averaging 0.40% WOз between 1955 and 1956. The mine closed when the Government buying program
ended. Mine workings include a 100’ X 50’ open-pit 25 feet deep, a 210’ shaft with approximately 1,500 feet of
drifts and cross-cuts. Shrinkage stopes extend from the 150’ level to the surface (Stager and Tingley, 1988).
In 1951, the Linka Mine was optioned to Hugh Chesser, Reno, NV. Hugh Chesser estimates shipments to
Metals Reserve Corporation during WWII totalled 2,673 tons averaging 0.72 percent WOз.
Cache Creek Exploration held the properties in the early 1970’s and conducted geological and geophysical
programs. Duval Corporation optioned the properties in the mid-1970’s, did geological studies but no drilling.
Min-Ex drilled the property in 1977-78, with a total of 73 drillholes recorded (eight DDH and 64 wide-spread
percussion drillholes). Note: Not all drillhole locations have been established, with 69 holes digitised and 1
hole estimated (total 70) and three percussion holes with unknown location. Exploration activity completed by
Minex included drilling, surface and underground geological mapping and sampling, minor geophysical
12
ASX:VKA, OTC:VKALF | vikingmines.com
Criteria JORC Code explanation Commentary
magnetic survey with 10,400 linear feet collected (inconclusive results), 6,500ft of bulldozer trenching and
mapping.
Stager and Tingley, 1988 estimate total production at the Linka mine at 25,670 units WOз (1943-56).
Linka-Conquest Mine: The mine was discovered in 1941 but did not start production until 1943 when Gale
Peer sunk a two-compartment inclined shaft to 130 feet. Workings off the shaft were at the 50 and 100 foot
levels. During WW II mined and shipped 390 tons of ore averaging 2.7% WOз. Additional shipments after the
War averaged over 1.0% WOз, but the tonnage is unknown. Last work on the 100’ level exposed a zone 40’
long, 12’ to 20’ wide, open to the northeast with a grade of <0.4% WOз. Stager and Tingley, 1988, estimate
total production at 5,208 units WOз (1944-56).
Stager and Tingley, 1988 estimate total production at the Conquest mine to be 5,208 units WOз (1944-56)
Geology Deposit type, geological setting and style of mineralisation
Linka Project: The area is underlain primarily by sedimentary rocks; it includes an outcrop of massive
limestone of Ordovician age (Upper Plate) overlain in thrust contact by chert and shale of Ordovician Vinini
Formation (Lower Plate). The limestone is intruded locally by granitic rocks of Jurassic age, and the tungsten
deposits occur in the limestone along the granite contact (Stager and Tingley, 1988)
Linka-Conquest Mine - Granite intrusive rocks (Jg) and aplite dikes intrude cherts, shales and limy members of
the Vinini Formation (Ov) in the Upper Plate of the Roberts Mountain Thrust. Scheelite-bearing skarn formed at
the contact.
Miocene age Bates Mountains tuff (Tbm) covers any extension of the mineralization to the northeast.
Linka Mine – Scheelite occurs in lenses and tabular masses of skarn at the contact between Ordovician
Antelope Valley Limestone (Lower Plate of the Roberts Mountain Thrust) and granitic intrusive rocks. The
contact zone is cut by igneous dykes and high-angle faults. Exposures are poor. Granite rocks west of the
contact zone are covered by post-mineral volcanic rock and sediments of Big Smokey Valley.
Antelope Valley limestone east of the contact zone is nearly vertical. The contact zone is about 40 feet wide.
Drilling in the 1970’s shows that, at depth, the contact zone may flatten to the east, then steepen.
Scheelite, with traces of chalcopyrite and molybdenite are the only ore minerals recognized.
Linka-Hillside - The Hillside incline shaft is about half way between the Conquest and Linka Mines. The shaft is
inclined at ~47° and is approximately 100 feet deep. In 1978, when the area was visited by Richard Jones and
Harold Bonham, geologists at the Nevada Bureau of Mines and Geology, there were no drifts or cross-cuts off
the shaft. Here the rocks are more thinly bedded and contain more hornfels then sediments at the Linka shaft.
Lenses of scheelite-bearing skarn in the Hanson Creek Fm are at the surface and a lens of mineralized skarn
within the Antelope Valley Limestone occurs in the shaft (Stager and Tingley, 1988).
Drill hole
Information
A summary of all information material to the understanding of the
exploration results including a tabulation of the following information for
all Material drill holes:
• easting and northing of the drill hole collar
• elevation or RL (Reduced Level – elevation above sea level in
metres) of the drill hole collar
• dip and azimuth of the hole
• down hole length and interception depth
• hole length.
If the exclusion of this information is justified on the basis that the
information is not Material and this exclusion does not detract from the
understanding of the report, the Competent Person should clearly explain
why this is the case.
Not applicable, no drilling is being reported.
13
ASX:VKA, OTC:VKALF | vikingmines.com
Criteria JORC Code explanation Commentary
Data
aggregation
methods
In reporting Exploration Results, weighting averaging techniques,
maximum and/or minimum grade truncations (e.g., cutting of high grades)
and cut-off grades are usually Material and should be stated.
Where aggregate intercepts incorporate short lengths of high-grade
results and longer lengths of low-grade results, the procedure used for
such aggregation should be stated and some typical examples of such
aggregations should be shown in detail.
The assumptions used for any reporting of metal equivalent values should
be clearly stated.
Not applicable, no drilling is being reported. No top cuts have been applied by Viking.
Relationship
between
mineralisation
widths and
intercept
lengths
• These relat
Share your feedback
Discover